Buyer guide · 6 min read ·
Pole-mounted transformer ratings guide: 10 to 167 kVA, CSP and conventional, voltages, BIL and mounting
Overhead distribution transformers are the most standardized product a utility buys, which is exactly why a specification should stay inside the standard. IEEE C57.12.20 covers single-phase units of 500 kVA and smaller with high voltage of 34,500 V and below. This guide covers the ratings most public utilities order and the choices that matter.
Standard kVA steps and voltages
| kVA | Typical use | Typical weight with oil (lb) |
|---|---|---|
| 10 | Rural single service, small loads | 250 to 350 |
| 15 | Single residence | 300 to 400 |
| 25 | One to three residences | 350 to 500 |
| 37.5 | Three to five residences | 450 to 650 |
| 50 | Small commercial, several residences | 550 to 800 |
| 75 | Commercial, well pumps | 750 to 1,050 |
| 100 | Commercial, small industrial | 900 to 1,300 |
| 167 | Commercial, three-phase banks | 1,300 to 1,900 |
Weights are typical for 15 kV class mineral-oil units and vary by manufacturer and design; use the outline drawing in the submittal for pole loading.
Primary voltages follow the system: 7200/12470Y V is the most common in the United States, followed by 7620/13200Y V, 14400/24940Y V and 2400/4160Y V on older systems. Secondary is 120/240 V for single-phase service; 240/480 V and 277/480Y V appear on commercial and three-phase bank applications. State both, and whether the primary bushing is one (grounded-wye, with the tank as the return) or two (delta or ungrounded systems).
CSP or conventional
A conventional transformer has no internal protection: the utility installs a fused cutout on the primary and, where wanted, an arrester on the crossarm. A completely self-protected (CSP) transformer has an internal primary fuse link, a secondary breaker with an overload signal light, and a tank-mounted arrester. The choice is a system-practice decision, not a quality one.
- Conventional: lower first cost, fewer failure modes inside the tank, easier to coordinate with the utility's fusing practice. Most larger utilities buy conventional.
- CSP: faster installation, built-in overload indication, useful for small crews and rural systems. The internal fuse is not replaceable in the field; a blown link means a shop visit.
- Either way, ask for the arrester rating and class (distribution class, 10 kA, typically 9 or 10 kV MCOV for 7.2 kV systems) if you want it supplied.
BIL, impedance and losses
- BIL: 95 kV for the 15 kV class, 125 kV for 25 kV class, 150 kV for 34.5 kV class. Reduced BIL is not worth the saving on a product this size.
- Impedance: C57.12.20 does not fix impedance for small units; manufacturers design in the 1.5 to 3.0 % range depending on kVA. Specify only if you have a coordination reason.
- Efficiency: DOE 10 CFR 431 levels apply from 10 kVA up. Ask for guaranteed no-load and load losses per kVA step and evaluate by total owning cost if you buy in volume.
- Temperature rise: 65 °C average winding rise is standard; a 55/65 °C dual rating buys 12 % overload capacity on paper and is rarely needed on a pole-top unit.
Mounting and hardware
Units through 167 kVA are supplied with two-position lifting lugs and a mounting bracket for direct pole mounting with two through-bolts; C57.12.20 standardizes the bracket dimensions. Specify the hanger type if your poles use cluster mounts for three-phase banks. Ask for the tank ground pad, the secondary bushing type (eyebolt or spade) and whether you want the nameplate on the pole side or the road side. These small items are what delay acceptance when they do not match the standard drawing.
Ratings and standards for the line we supply are on the pole-mounted product page; the submittal package is listed on the compliance page.
Frequently asked.
- Is 167 kVA the largest single-phase pole-mount?C57.12.20 covers up to 500 kVA, but above 167 kVA most utilities move to pad-mounted or platform-mounted units because of pole loading.
- Can a 7200 V unit be used on a 7620 V system?Only within the tap range and with reduced margin. Order the voltage your system uses.
- What is the typical warranty?One year from energization or eighteen months from shipment is the common manufacturer term; longer terms can be quoted.
- Do you supply three-phase banks?Three single-phase units with matching ratings and impedance are quoted as a bank on request; state the bank connection in the RFQ.
Send ratings, quantities and a delivery point.
We reply within one business day with price, lead time from a named manufacturer and the submittal package described on the compliance page.